Barbie Fondant Cake
1.
【Materials for making cake embryo:】
2.
Soak the raisins in rum for later use
3.
After the butter is naturally softened, use an electric whisk to disperse it, and then add the sifted powdered sugar
4.
Use a silicone spatula to mix until there is nothing powdery, and then use an electric whisk to beat evenly
5.
Add the eggs in three times and beat them evenly. Each time you add the eggs, you must fully beat and fuse and then add another egg.
6.
Sift in low-gluten flour, baking powder and cinnamon powder in batches, and mix evenly with a spatula
7.
Finally add the raisins soaked before, drain and add the raisins, mix well with a spatula.
8.
Pour the cake batter into 4-inch and 6-inch molds, and scrape the surface slightly
9.
Put the mold into the oven, and bake the middle and lower layers at 170 degrees for about an hour. When you bake it with a toothpick and take it out, there is no wet sticky material on the toothpick and it can be taken out and cooled for use. TIPS: 1. Pay attention to the process of baking Observe the degree of coloring. If the surface is darker and the inside is not fully cooked, you can cover the surface of the cake with a layer of oil paper or tin foil and continue baking until it is fully cooked.
10.
[Materials for making butter cream:]
11.
Beat the eggs for a while and foam
12.
Boil water and sugar to 125 degrees
13.
Continue to beat the eggs, add the cooked sugar water while beating, continue to beat until the temperature drops
14.
Beat the eggs and sugar water until the outside of the utensil is not hot, add soft butter in portions while beating
15.
After adding the butter, stir evenly and set aside
16.
[Barbie fondant cake making] 1. First put the 4-inch cake embryo on the 6-inch cooled cake embryo, use a knife to cut the periphery into an arc, and then dig a small hole in the middle. The hole should not be too large and can be put in The villain will do
17.
Then put butter cream frosting on the middle and the periphery of the two cakes to stick the two cakes together.
18.
Take a little fondant paste and knead it into several small round strips and paste on the periphery of the cake
19.
Then take an appropriate amount of fondant cream and use a rolling pin to roll it into a big circle to make a skirt, and a circle hole is carved out in the middle
20.
Cover the big round piece on the cake, and place the hole of the round piece facing the hole of the cake. Use your hands to arrange the cake in a circle to make a nice skirt
21.
Wrap the body of the villain with tin foil, then take a small amount of fondant cream and roll it into a thin piece. The long piece should be able to cover the middle part of the villain. Wrap the villain face down with a face sheet, and cut and glue it to the back. interface
22.
Then turn Barbie over and adjust the clothes by hand
23.
Then cut a small strip, apply a little honey to make an adhesive and stick it on the neckline to make a collar
24.
Use the smallest flower fondant mold to carve small flowers, and then use the smallest ball tool to press a hole in the middle of the flower, and the small ball tool to glue some honey and then press it in the middle hole of the flower for adhesion, and then put a pearl candy decoration.
25.
Then spread a little honey on the back of the finished flower and stick it on the Barbie collar
26.
Then insert the Barbie with the upper body dressed in the middle of the cake with the skirt spread on the front, and then cut out a small circle hole in the middle in the same way, and then cut off the connection between the Barbie body and the cake.
27.
Then look at the ratio and carve out a fondant circle that is slightly larger but smaller than the bottom skirt, with a hole in the middle, and a small circle with a small round hole in the front of the round flower mouth, and then cut off one side
28.
Then stick it on Barbie's body and the interface of the cake to wrap the layer that was pasted in front and don’t expose it.
29.
Then cut a thin strip and stick it to the crotch of Barbie's body, wrap up the interface of the upper skirt, and wrap the thin strip to the back and cross and divide it as a bow ribbon. The long strip at one end can be used to cover the back skirt interface. Live, make a small bow and stick it behind Barbie, and stick it to the cross of the ribbons
30.
Finally, stick a circle of the same small flower on the collar under the skirt, and then make a slightly larger pink flower and stick it on the slender strip below Barbie’s waist for decoration
31.
Finished~
32.
...
33.
...
34.
...
35.
...
36.
...
Tips:
TIPS:
1. Therefore, honey is used as an adhesive in the process of bonding. The honey cannot be applied too much, it will flow down after a long time.
2. Barbie clothes can be made according to your favorite style
3. The bow on the back should not be too thick or too big, otherwise it will fall off easily
4. The size of the two-layer skirt has to be engraved by yourself with a suitable mold. The large round piece can be rolled with a rolling pin to make the skirt longer. It is okay to find a suitable round object for the upper skirt. It’s best to have a big round fondant mold