Barbie Fondant Cake
1.
【Materials for making cake embryo:】
2.
1. Soak the raisins with rum for later use
3.
2. After the butter is naturally softened, use an electric whisk to disperse it, and then add sifted powdered sugar
4.
3. Use a silicone spatula to mix until there is nothing powdery, and then use an electric whisk to beat evenly
5.
4. Add the eggs in three times and beat them evenly. Each time you add eggs, you must fully beat them and then add another egg.
6.
5. Sift in low-gluten flour, baking powder and cinnamon powder in batches, and mix evenly with a spatula
7.
6. Finally add the raisins soaked before, drain and add the raisins, mix well with a spatula.
8.
7. Pour the cake batter into 4-inch and 6-inch molds, and scrape the surface slightly
9.
8. Put the mold into the oven, and bake the middle and lower layers at 170 degrees for about an hour. When you bake it with a toothpick and take it out, there is no wet sticky material on the toothpick, then it can be cooled and ready for use.
TIPS:
1. Pay attention to the degree of coloring during the baking process. If the surface is darker and the inside is not yet fully cooked, you can cover the surface of the cake with a layer of oil paper or tin foil and continue baking until it is fully cooked.
10.
[Materials for making butter cream:]
11.
1. Beat the eggs for a while and foam
12.
2. Boil water and sugar to 125 degrees
13.
3. Continue to beat the eggs, add the cooked sugar water while beating, continue to beat until the temperature drops
14.
4. Beat the eggs and sugar water until the outside of the utensil is not hot, add soft butter while beating
15.
5. After adding the butter, stir evenly and set aside
16.
【Making Barbie Fondant Cake】
1. First put the 4-inch cake embryo on the 6-inch cooled cake embryo, use a knife to cut the periphery into an arc, and then dig a small hole in the middle. The hole should not be too big, and it can be put into a small person.
17.
2. Then put butter cream frosting on the middle and the periphery of the two cakes to stick the two cakes together
18.
3. Take a little fondant paste, knead into a few small round strips and paste on the periphery of the cake
19.
4. Take an appropriate amount of fondant cream and use a rolling pin to roll it into a big circle to make a skirt, and a circle hole is carved out in the middle
20.
5. Cover the big round piece on the cake, and place the hole of the round piece facing the hole of the cake. Use your hands to arrange the cake in a circle to make a nice skirt
21.
6. Wrap the body of the villain with tin foil, then take a small amount of fondant cream and roll it into a thin piece. The long piece should be able to cover the middle part of the villain. Wrap the villain face down with a face sheet, and cut it out with the interface facing the back. Glue the interface
22.
7. Turn Barbie over and adjust the clothes by hand
23.
8. Cut another small strip, apply a little honey to make an adhesive and stick it on the neckline to make a collar
24.
9. Use the smallest flower fondant mold to carve small flowers, and then use the smallest ball tool to press a hole in the middle of the flower, and the small ball tool to glue some honey and then press it in the middle hole of the flower for adhesion, and then place another one Pearl sugar decoration.
25.
10. Then spread a little honey on the back of the finished flower and stick it on the Barbie collar
26.
11. Then insert Barbie with the upper body dressed in the middle of the cake with the skirt spread on the front, and then cut a small circle hole in the middle in the same way, and then cut off the interface between the Barbie body and the cake.
27.
12. Then look at the ratio and carve out a fondant circle that is slightly larger but smaller than the bottom skirt, with a hole in the middle, and a small circle with a small round hole in the front of the round flower mouth, and then cut off one side
28.
13. Stick it on Barbie's body and the interface of the cake to wrap the layer that was pasted in front and don't expose it.
29.
14. Cut another slender strip and stick it on the crotch of Barbie's body, and wrap the interface of the upper layer of the skirt. The slender strip is wrapped around the back and crossed and separated as a bow ribbon. Cover it, make a small bow and stick it behind Barbie, and stick it to the cross of the ribbon
30.
25. Finally, stick a circle of the same small flower on the collar under the skirt, and then make a slightly larger pink flower and stick it on the slender strip below Barbie’s waist for decoration
Tips:
TIPS:
1. Therefore, honey is used as an adhesive in the process of bonding. The honey cannot be applied too much, it will flow down after a long time.
2. Barbie clothes can be made according to your favorite style
3. The bow on the back should not be too thick or too big, otherwise it will fall off easily
4. The size of the two-layer skirt has to be engraved by yourself with a suitable mold. The large round piece can be rolled with a rolling pin to make the skirt longer. It is okay to find a suitable round object for the upper skirt. It’s best to have a big round fondant mold