by Green String Xiaoxiang
Difficulty
Hard
Time
2h
Serving
2
1. Sift the low-gluten flour and set aside, separate the egg yolk and egg white, and put the egg white in the refrigerator
2. After the cream cheese heat insulation water is softened, add milk and butter, continue to heat the heat insulation water and stir until it is smooth (because the amount is small, I added the butter and milk together to stir). Take it out of the hot water pot and put it on the table to continue the operation
3. Stir until it is smooth, add lemon juice (2ml is very small, you can directly hold the lemon and squeeze it into the basin) and continue to stir until it is smooth
4. Add egg yolk and stir well
5. Sift in the flour and stir to form a batter for later use
6. Cover with a wet towel to prevent the surface of the batter from drying out (at this time, you can set the upper and lower fire temperature of the oven to 160 degrees to start preheating)
7. Take out the egg white from the refrigerator, you can see that a thin layer of ice has formed on the edge of the egg white, so that the egg white will be more stable after foaming
8. Squeeze a few drops of lemon juice to make coarse bubbles, add fine sugar (also because of the small amount, add it all at once)
9. Slowly beat at medium and low speed until wet foaming, just lift the whisk to see the sharp corners as shown in the figure.
10. Dig a piece of meringue into the egg yolk paste and mix until it is roughly uniform (the purpose of this step is to reduce the density of the egg yolk paste to prevent it from sinking when mixing, so it does not need to be too uniform)
11. Then pour it into the meringue basin and stir evenly. (Be careful not to circle or spirally stir. Use a spatula to cut from the middle of the meringue and shovel the bottom of the spatula to the side of the spatula. Shovel it to the side of the basin. Up, then press down to the center of the basin and turn over to continue cutting and mixing. Until there is no unmixed meringue)
12. Pour into the mold about eighth full
13. Insert the baking pan filled with hot water in the bottom layer of the preheated oven, insert the baking net in the upper layer of the baking pan, put the mold with cake batter on the baking net, adjust the upper and lower heat to 150℃ and bake about 45 -50 minutes, then adjust to 180 degrees until the color is released
14. Place it on a wire rack to dry for 2 minutes. The sides of the cake will separate from the mold. This time is the best time to demold. Take the cake mold on its side, turn it a few times, cover a flat base, turn it over and buckle out the cake
15. Put another small plate on the cake, and turn the cake upside down, so that the cake comes straight. Look, is it perfect?
Tips:1 If the cream cheese is added to the milk without first softening, particles are likely to appear when stirring, so first soften the cheese insulation water before adding the milk. In addition, because of the small amount this time, I added the butter and milk together and stirred. If you are making a large cheesecake, melt the butter first, add milk and stir it smoothly, then add the melted butter. That makes it easier to stir)
2 Everyone knows that baking cheese, cakes and puddings are all baked in a water bath method, that is, when baking, put the touch tool in water, so that the baked cheesecake is delicate and moist and melts in the mouth. However, if it is not done well, water will enter the bottom of the mold. Sometimes water enters after a few layers of tin foil. So now I always bake in water, that is, put a baking tray on the bottom layer of the oven and fill it with water. The oven is the second to last. Insert the baking net in layers and bake the cake on top. In this way, there is no need to worry about water in the mold, and the cake will not be dried out. (Although I used a solid mold this time, I still used this method. After all, if you put it directly in water, you must also consider how much water should be placed in the baking pan: there is more water, and the mold floats. No; if there is less water, it won’t work if it evaporates while baking.)
3 Generally speaking, it is best to use non-stick molds for baking light cheese. The side of the cake will be separated from the mold two minutes after it is out of the oven. If it is a movable bottom mold, then slowly push the bottom up by hand to remove it. , At this time, the untouched cake will be very beautiful and will not shrink. If it is a solid mold, invert the cake into a flat bottom plate, and then invert it into another plate, the cake will be straight. If you don’t have a non-stick mold or are not so confident about the anti-sticking effect of your mold, put a layer of butter on the sides and bottom of the mold, and release the mold in the same way









